又是一年月圆时，波妞先在这里祝大家中秋节快乐！

提起中秋节，就不得不说说月饼

在古中国，人们把互赠月饼以表团圆之意

月饼发展到现在，已经演化出了各种口味

不知道你最喜欢吃的是什么口味的月饼呢？

活动一

带上月饼的图片来和大家说说你最喜欢的月饼吧！

在本贴回复“我最喜欢的月饼口味以及理由+自己拍的月饼照片”，即可参加本次活动

参加即可获得中秋限定勋章

另外波妞会选取10位最佳回复额外赠送100博币和100积分

活动时间：9.17-9.21日

快带上你的月饼来参加吧~

活动二

花费10新博币参与投票，选出你心中的“最佳月饼”

参与投票后会人工扣除10新博币用以竞猜

活动结束后，“最佳月饼”的投注者们将获得3倍博币奖励（本金+奖励共30新博币）

活动时间：9.17-9.21日

快来支持你的“最佳月饼”吧

活动三——广告合作

在此次中秋节活动期间享受，所有合作享受以下广告福利：

1、购买博牛招聘首页广告栏，八折优惠

2、购买博牛招聘简历套餐2 ，九折优惠

广告合作联系TG：  @Jerry0003 @Kevin_HH @Sum886

中秋活动圆满结束，感谢大家的参与和支持~~

活动一的中奖用户为：你能成大事！,shanshan123,makati老三,xinmiao888,马尼拉不热,汉堡哥,风月佳人,CK哥,MrJim,xiaolinzi

活动二的获胜月饼为：莲蓉蛋黄月饼！

奖励会陆续发至各位的账号，请注意查收~

哇。错过了。

每日疫情打卡+（你的健康

谢谢您的分享 好故事

谢谢你的分享

谢谢你的分享

<h2>  Using the Balanset-1A Instrument  </h2>

<h3>  Equipment Preparation   </h3>
<ul>
<li>  accelerometers, laser rpm sensor, mounting stand, software application, and additional tools.  </li>
<li>   Set up the instrument and connect it to your computer via USB. Verify that the software is correctly installed.    </li>
</ul>

<h3>   Mounting the Sensors  </h3>
<ul>
<li>  Attach the vibration sensors firmly to the machine casing in areas with the highest vibration amplitude, usually close to the bearing supports.  </li>
<li>   Position the laser tachometer (phase angle sensor) so that it is aimed at the rotor. Attach reflective tape to the rotor for accurate phase angle reading.    </li>
</ul>

<h3> Launching the Software  </h3>
<ul>
<li>   Initiate the Balanset program on your computer.  </li>
<li>   Select the appropriate balancing mode: single-plane or two-plane, depending on the rotor type and your specific requirements.    </li>
</ul>

<h3>  Measuring Initial Vibration  </h3>
<a href="https://vibromera.eu/wp-content/uploads/2024/11/2-Camera_01.png" target="_blank">

</a>
<ul>
<li>   Run the rotor up to its operating speed.    </li>
<li>   The software will measure the vibration level, rotational speed, and phase angle. This data establishes the current imbalance condition.    </li>
</ul>

<h3> Trial Weight Installation   </h3>
<a href="https://vibromera.eu/wp-content/uploads/2024/11/3-Camera-2_01.png" target="_blank">

</a>
<ul>
<li>   Stop the rotor and attach a trial weight at a specific location on the rotor. The weight's mass can be specified within the software (e.g., in grams).    </li>
<li>   Restart the rotor, and the software will record the changes in vibration level and phase angle.    </li>
</ul>
<a href="https://vibromera.eu/wp-content/uploads/2024/11/5-Camera_01.png" target="_blank">

</a>


<h3> Calculating the Correction Weight   </h3>
<ul>
<li>   Based on the measured data, the software automatically calculates the correction weight parameters: mass and installation angle.    </li>
<li>   These parameters are displayed on the screen as numerical data and graphs.    </li>
</ul>
<a href="https://vibromera.eu/wp-content/uploads/2024/02/Bs1ManualEngV156-May2023-10448629.png" target="_blank">

</a>

<h3> Installing the Correction Weight   </h3>
<ul>
<li>  Mount the calculated corrective weight onto the rotor at the specified location and angle.  </li>
<li>   You can conduct interim measurements to confirm that the imbalance is decreasing as expected.  </li>
</ul>
<a href="https://vibromera.eu/wp-content/uploads/2024/11/1-Camera-2_01.png" target="_blank">

</a>

<h3> Validation and Conclusion of the Balancing Process  </h3>
<ul>
<li>   Once the corrective weight is in place, restart the rotor and measure the remaining vibration amplitude.  </li>
<li>  If the measured vibration falls within the tolerance defined by ISO 1940, the balancing process is considered successful.  </li>
<li>   Should the vibration still be excessive, repeat the balancing steps, making further adjustments to the corrective weight as needed.  </li>
</ul>

<h3> Generating a Documentation of the Balancing Results  </h3>
<ul>
<li>  The program stores the balancing data, allowing you to generate and print a comprehensive report including vibration measurements, corrective weight details, and its angular placement.  </li>
</ul>

<h3> Concluding Steps and Verification  </h3>
<ul>
<li>  Ensure all applied weights and attached sensors are firmly fixed in their designated positions.  </li>
<li>   Check that the rotor's rotation is smooth and free from undue noise or vibration.  </li>
<li>   In cases where the rotor is integrated into a more complex system, ensure the correct operation and interaction of all related components.  </li>
</ul>

<p>     </p>




Instagram: https://www.instagram.com/vibromera_ou/
Youtube :  https://youtu.be/guA6XJ-ArZM?si=vmkuX7RILzKBl0zL  
Our website about  <a href="https://vibromera.eu   
"> Balancing of mixer rotors </a>